We Select Texas Business Blog

The Largest Business Blog in Texas

Month: March 2023 Page 1 of 5

How to Seal Gap at Top of Your Garage Door – Springtown TX Garage Door

By

On March 31, 2023

In Garage Door

If you have a gap at the top of your garage door, it can allow unwanted air and debris to enter your garage. Fortunately, there are several ways to seal this gap.

Here are some steps from Garage Door Repair Springtown TX that you can follow to seal the gap at the top of your garage door:

  1. Measure the gap

Start by measuring the gap at the top of your garage door. Use a tape measure to determine the width of the gap, as well as the height and depth.

  1. Choose a seal type

There are several types of seals available that can be used to seal the gap at the top of your garage door. Some popular options include weatherstripping, brush seals, and rubber seals.

  1. Install the seal

Once you have chosen a seal type, follow the manufacturer’s instructions for installing it. Weather-stripping and rubber seals can typically be installed using adhesive, while brush seals may require screws or other hardware.

  1. Test the seal

After installing the seal, close the garage door and check for any gaps. You may need to adjust the seal to ensure that it is fully covering the gap.

  1. Check for additional gaps

In some cases, there may be additional gaps around the sides or bottom of the garage door. Check for any additional gaps and install seals as needed.

  1. Maintain the seal

To ensure that the seal remains effective, it is important to maintain it properly. Clean the seal regularly to remove any dirt or debris that may accumulate on it. Additionally, check the seal periodically to ensure that it is still in good condition and replace it if necessary.

Lastly, as stated in Garage Door Repair Springtown TX, you should be able to effectively seal the gap at the top of your garage door. This can help to keep your garage clean, dry, and free from unwanted air and debris.

Springtown TX Garage Door

205 Ave A, Springtown, TX 76082

817-373-5963

How to Fix a Garage Door Opener Motor? – Affordable Garage Door of Hamilton County

By

On March 31, 2023

In Garage Door

Fixing a garage door opener motor can be a bit tricky, but it’s possible to diagnose and repair many issues with the right tools and knowledge.

Here are some common steps from Garage Door Repair Hamilton IN that you can take to fix a garage door opener motor:

  1. Identify the problem

Before you can fix your garage door opener motor, you need to identify the problem. Common issues include the door not opening or closing properly, the motor making strange noises, or the motor not working at all.

  1. Check the power source

One of the first things to check is the power source. Make sure that the motor is properly plugged in and that the outlet is working. You should also check the circuit breaker to make sure it hasn’t been tripped.

  1. Inspect the motor

Once you’ve confirmed that the motor is receiving power, it’s time to inspect the motor itself. Look for any visible signs of damage or wear, such as broken wires or a burned out motor.

  1. Check the gears and drive system

If the motor appears to be in good condition, the issue may be with the gears or drive system. Check the gears and drive system for any signs of damage or wear, such as broken teeth or worn-out belts. If the gears or drive system appear to be damaged, they may need to be replaced.

  1. Lubricate moving parts

If the gears and drive system are in good condition, but the motor is still not working properly, the issue may be due to lack of lubrication. Use a lubricant specifically designed for garage doors to lubricate the moving parts of the door, such as the tracks, rollers, and hinges.

  1. Reset the motor

If none of the above steps resolve the issue, try resetting the motor. This can be done by unplugging the motor and leaving it unplugged for several minutes before plugging it back in. This may reset any sensors or other components that may be causing the issue.

  1. Call a professional

If you’re unable to diagnose or fix the issue on your own, it may be time to call a professional garage door technician. A technician can diagnose and repair more complex issues with your garage door opener motor and ensure that the system is working safely and efficiently.

Based from Garage Door Repair Hamilton IN, fixing a garage door opener motor can be a bit challenging, but by following these steps and taking the necessary precautions, you can often repair many issues on your own. If you’re unsure about how to fix your garage door opener motor, or if you’re not comfortable working with electrical systems, it’s always best to seek the assistance of a professional.

Affordable Garage Door of Hamilton County

27361 Mosbaugh Rd. Arcadia, IN 46030

317-342-8167

How Much are Electric Garage Door Openers? – Lakewood Garage Door Repair

By

On March 30, 2023

In Uncategorized

Electric garage door openers are a popular and convenient addition to many homes. The cost of an electric garage door opener can vary depending on a number of factors, including the type of opener, the horsepower of the motor, and any additional features or accessories that are included.

As stated in Garage Door Lakewood OH, at the time of writing this answer in March 2023, electric garage door openers range in price from approximately $150 to $500 or more. The price includes the cost of the opener itself, as well as any installation or delivery fees that may apply.

There are several types of electric garage door openers available, including chain drive, belt drive, and screw drive openers. Chain drive openers are the most common and typically the least expensive. They use a chain to pull the door along the track, and they can be noisy. Belt drive openers use a belt instead of a chain, which makes them quieter but more expensive. Screw drive openers use a threaded rod to lift the door and are generally quieter than chain drive openers but can be more expensive.

The horsepower of the motor also plays a role in the cost of an electric garage door opener. Motors are typically available in 1/2, 3/4, and 1 horsepower options. A more powerful motor can lift heavier doors and may be necessary for larger or heavier doors. However, a more powerful motor can also be more expensive.

Additional features or accessories can also add to the cost of an electric garage door opener. For example, some openers come with a battery backup system that allows the opener to operate during power outages. Other openers come with Wi-Fi connectivity, allowing the homeowner to control the opener using a smartphone app. Safety features such as infrared sensors, which detect objects in the path of the door and stop it from closing, can also add to the cost of an opener.

Installation fees can also add to the total cost of an electric garage door opener. The cost of installation can vary depending on the complexity of the installation, the location of the installation, and any additional work that may be required.

It is important to consider the total cost of an electric garage door opener when making a purchase. While a less expensive opener may seem like a good deal, it may not have the features or horsepower necessary to properly lift and operate the door. It is also important to ensure that the opener is compatible with the type and size of the door being installed.

Overall, as per Garage Door Lakewood OH, the cost of an electric garage door opener can vary depending on a number of factors. It is important to carefully consider the type of opener, horsepower, and any additional features or accessories when making a purchase. Professional installation may also be necessary, which can add to the total cost of the opener.

Lakewood Garage Door Repair

1422 Elmwood Ave #7, Lakewood, OH 44107, United States

216-510-9359

How Garage Door Remote Works – First Call Garage Door Sugar Land

By

On March 30, 2023

In Garage Door

A garage door remote is a device used to control the operation of a garage door opener from a distance. The remote sends a signal to the opener to activate the motor and open or close the garage door. In this article, we will explain how garage door remotes work.

As stated in Garage Door Repair Missouri TX, garage door remotes use radio signals to communicate with the opener unit. When a button is pressed on the remote, it sends a coded signal in the form of radio waves to the receiver in the opener unit. The receiver unit decodes the signal and triggers the motor to move the door up or down.

The remote control usually operates on batteries, and when a button is pressed, the battery sends an electrical current through a circuit that generates a radio signal. This signal is typically in the 300-400 MHz frequency range, which allows it to pass through walls and other obstructions. The remote control sends the signal at a specific frequency that is unique to that particular opener, and the opener unit is programmed to respond only to that specific frequency.

Most modern garage door remotes use a rolling code system, which means that the code changes each time the remote is used. This provides additional security by preventing unauthorized access to the garage by making it more difficult for someone to intercept and duplicate the signal. Rolling code remotes generate a new code each time a button is pressed, which is sent along with the radio signal to the opener unit. The opener unit is also programmed to generate the same code, and when it receives the correct code, it activates the motor to open or close the garage door.

There are several types of garage door remotes, including fixed-code remotes, dip-switch remotes, and rolling code remotes. Fixed-code remotes use a fixed code that is programmed into both the remote control and the opener unit. This code is easy to duplicate, and it provides little security. Dip-switch remotes use a series of switches that can be set in different combinations to generate a unique code. While dip-switch remotes are more secure than fixed-code remotes, they can still be vulnerable to hacking or duplication. Rolling code remotes are the most secure, as they generate a new code each time they are used.

In addition to the remote control, garage door openers can also be operated using a keypad, which allows users to enter a code to activate the opener. Keypads are typically mounted outside the garage, and they are useful for providing access to the garage without the need for a remote control. Some garage door openers also come with built-in buttons that can be used to open or close the door manually.

Overall, as stated in Garage Door Repair Missouri TX, garage door remotes use radio signals to communicate with the opener unit, and they typically operate on batteries. Most modern garage door remotes use a rolling code system, which provides increased security by generating a new code each time the remote is used. By understanding how garage door remotes work, homeowners can choose the right remote for their needs and ensure that their garage door opener operates smoothly and securely.

First Call Garage Door Sugar Land

2865 Dulles Ave, Missouri City, TX 77459, United States

281-603-9929

How Do You Paint an Aluminum Garage Door – LMS Garage Door Roseville

By

On March 29, 2023

In Garage Door

Painting an aluminum garage door can be a great way to update the look of your home and increase its curb appeal. However, aluminum can be tricky to paint because it is a non-porous surface, meaning it doesn’t absorb paint easily.

In this guide, according to Garage Door Repair Roseville CA, we will take you through the step-by-step process of painting an aluminum garage door.

Materials Needed:

  • Sandpaper (220 grit)
  • Tack cloth
  • Painter’s tape
  • Drop cloths
  • Etching primer for metal
  • Paint (acrylic or oil-based)

Step 1: Clean the Surface The first step in painting an aluminum garage door is to thoroughly clean the surface. Use a mild detergent and water to remove any dirt, dust, or debris from the door. Rinse the door with clean water and allow it to dry completely before moving on to the next step.

Step 2: Sand the Surface Once the surface is clean and dry, use a 220-grit sandpaper to lightly sand the door. This step helps to create a rough surface that the primer can adhere to. Use a tack cloth to remove any dust or debris left behind after sanding.

Step 3: Apply Painter’s Tape Use painter’s tape to cover any areas of the garage door that you do not want to paint. This may include the door handles, windows, or any other hardware.

Step 4: Apply Etching Primer Apply a primer specifically designed for use on metal surfaces. Etching primer is recommended for aluminum garage doors as it helps to create a surface that paint can adhere to. Apply a thin coat of primer to the entire surface of the garage door. Use a brush or roller to apply the primer, and be sure to follow the manufacturer’s instructions for drying time.

Step 5: Sand the Surface Again Once the etching primer is dry, use a 220-grit sandpaper to lightly sand the surface again. This step helps to create an even smoother surface for the paint to adhere to. Use a tack cloth to remove any dust or debris left behind after sanding.

Step 6: Apply the Paint Apply the paint to the surface of the garage door using a brush or roller. Be sure to use a paint that is specifically designed for use on metal surfaces. Apply a thin coat of paint and allow it to dry completely before applying additional coats. Follow the manufacturer’s instructions for drying time and number of coats needed.

Step 7: Remove the Painter’s Tape Once the paint is completely dry, carefully remove the painter’s tape from the garage door.

Tips and Tricks:

  • Be sure to apply the paint in thin, even coats to prevent drips and runs.
  • Use a high-quality brush or roller to ensure a smooth finish.
  • If you need to apply multiple coats of paint, be sure to lightly sand the surface with 220-grit sandpaper between coats.
  • If you are using an oil-based paint, be sure to properly dispose of any rags or other materials that have come into contact with the paint to prevent the risk of fire.
  • Avoid painting in extreme temperatures or direct sunlight, as this can affect the drying time and the final finish.

In conclusion, according to Garage Door Repair Roseville CA, painting an aluminum garage door requires proper preparation and the use of the right materials and techniques. By following the step-by-step process outlined above, you can achieve a smooth, long-lasting finish that will enhance the appearance of your home.

LMS Garage Door Roseville

10341 Fairway Dr, Roseville, CA 95678, United States

916-398-2078

How to Repair Garage Door Spring – Acclaim Garage Door of Chandler

By

On March 28, 2023

In Garage Door

Garage door springs are one of the most important components of your garage door system. They help to counterbalance the weight of the door and allow it to open and close smoothly. When a garage door spring breaks, it can be a major inconvenience and a safety hazard.

In this article, we will discuss how to repair a garage door spring according to Garage Door Repair Chandler AZ.

Before we get started, it’s important to note that garage door spring repair can be dangerous and should only be attempted by experienced individuals. If you’re not comfortable performing the repair yourself, consider hiring a professional garage door technician.

Step 1: Identify the Problem The first step in repairing a garage door spring is to identify the problem. There are two types of garage door springs: torsion springs and extension springs. Torsion springs are located above the garage door and are typically mounted on a metal shaft. Extension springs are located on either side of the door and stretch or expand to counterbalance the weight of the door.

If you hear a loud bang or notice that the door is crooked or uneven, it may be a sign that one of the springs has broken. You may also notice that the door is difficult to open or close, or that it makes a grinding or squeaking noise when in use.

Step 2: Release Tension from the Spring Before attempting to repair a garage door spring, it’s important to release the tension from the spring. This can be done by disconnecting the garage door opener from the door and manually lifting the door until the spring is fully extended. Be sure to use caution when lifting the door, as it will be heavy and may be difficult to control.

Step 3: Remove the Broken Spring Once the tension has been released from the spring, it’s time to remove the broken spring. If you have a torsion spring, use a winding bar to loosen the set screws on the winding cone. Then, slide the spring off of the shaft and remove it from the bracket. If you have an extension spring, use a pair of pliers to remove the safety cable from the extension spring. Then, use a socket wrench to loosen the bolts that hold the spring in place. Once the bolts are removed, slide the spring off of the bracket.

Step 4: Install the New Spring After the broken spring has been removed, it’s time to install the new spring. If you have a torsion spring, slide the new spring onto the shaft and tighten the set screws on the winding cone. Be sure to wind the spring in the correct direction, as specified by the manufacturer. If you have an extension spring, slide the new spring onto the bracket and secure it in place with the bolts. Then, reattach the safety cable to the spring.

Step 5: Test the Door Once the new spring has been installed, it’s time to test the door to make sure that it is operating smoothly. Reconnect the garage door opener to the door and test the door to ensure that it opens and closes smoothly and without any sticking or jerking.

Additional Tips:

  • It’s important to replace both springs at the same time, even if only one of them has broken. This will ensure that the door is properly balanced and will prevent future problems.
  • When installing a new spring, be sure to use a spring that is the same size and rating as the old one. Using the wrong size or rating of spring can cause damage to your garage door system.
  • If you’re not comfortable repairing a garage door spring yourself, consider hiring a professional garage door technician to perform the repair for you.

In conclusion, as per Garage Door Repair Chandler AZ, repairing a garage door spring can be a challenging task that requires experience and caution. By following the steps outlined above, you can ensure that your garage door is properly repaired and operating safely and smoothly.

Acclaim Garage Door of Chandler

184 E Chilton Dr, Chandler, AZ 85225, United States

480-545-0538

How to Make Your Garage Door Insured – Acclaim Garage Door Repair of Phoenix

By

On March 28, 2023

In Garage Door

Garage doors are an important part of many homes, providing a safe and secure space to park vehicles and store items. However, garage doors can also be a significant liability if they are not properly insured.

In this article based from Garage Door Phoenix AZ, we’ll discuss how to make your garage door insured and protect yourself against potential damage or accidents.

  1. Check your homeowner’s insurance policy: The first step in insuring your garage door is to review your homeowner’s insurance policy. This policy should cover damage to your garage door caused by fire, theft, or other covered events. However, it’s important to check the specifics of your policy to ensure that your garage door is covered.
  2. Add coverage if necessary: If your homeowner’s insurance policy does not provide adequate coverage for your garage door, you may need to add additional coverage. This can be done by adding an endorsement to your existing policy or by purchasing a separate garage door insurance policy.
  3. Choose the right coverage: When choosing coverage for your garage door, consider the type of damage that you want to be covered for. For example, if you live in an area with a high risk of natural disasters, you may want to choose coverage that includes protection against wind, hail, or flooding.
  4. Document your garage door: To ensure that your garage door is properly insured, it’s important to document its condition and value. Take pictures of your garage door from different angles, and make note of any existing damage or wear and tear. Keep this documentation in a safe place, as you may need to provide it to your insurance company in the event of a claim.
  5. Maintain your garage door: Proper maintenance of your garage door is essential to ensure that it functions properly and remains insured. Regularly inspect your garage door for any signs of damage or wear and tear, and have it serviced by a professional if necessary.
  6. Choose a reputable garage door company: When installing or repairing your garage door, choose a reputable company with experience in the industry. This will help ensure that your garage door is installed correctly and that any necessary repairs are done properly.
  7. Consider a warranty: Some garage door manufacturers offer warranties that cover damage or defects for a certain period of time. Consider purchasing a warranty for your garage door to provide additional protection against unexpected damage.

In conclusion, according to Garage Door Phoenix AZ, insuring your garage door is an important part of protecting your home and belongings. By reviewing your homeowner’s insurance policy, adding coverage if necessary, choosing the right coverage, documenting your garage door, maintaining it properly, choosing a reputable garage door company, and considering a warranty, you can ensure that your garage door is properly insured and protected against potential damage or accidents.

Acclaim Garage Door Repair of Phoenix

1107 E Bell Rd UNIT 16, Phoenix, AZ 85022, United States

602-833-1218

How Often Do You Need to Replace Your Garage Door Springs – Garage Door Experts of Boynton Beach

By

On March 24, 2023

In Garage Door

The garage door springs are an essential component of your garage door system that help balance the weight of the door and make it easier to open and close. Over time, garage door springs can become worn or damaged, which can affect the performance of your door and pose a safety risk.

Here are some general guidelines for how often you may need to replace your garage door springs in reference to Garage Door Boynton Beach FL:

  1. Torsion Springs – Torsion springs are the type of spring that is mounted above the garage door opening and wound tightly to provide the lifting force needed to open and close the door. Torsion springs are typically rated for a certain number of cycles, which refers to the number of times the spring can be wound and unwound before it starts to weaken. A typical torsion spring may be rated for 10,000 to 20,000 cycles, which could translate to anywhere from 5 to 15 years of use depending on the frequency of use.
  2. Extension Springs – Extension springs are the type of spring that is mounted on either side of the garage door and stretched tightly to provide the lifting force needed to open and close the door. Extension springs are typically rated for a certain number of cycles, similar to torsion springs. A typical extension spring may be rated for 10,000 to 20,000 cycles, which could translate to anywhere from 5 to 15 years of use depending on the frequency of use.

It’s important to note that these are general guidelines, and the lifespan of your garage door springs may vary depending on several factors, including the quality of the materials, the weight of your garage door, the frequency of use, and the level of maintenance performed. Regular maintenance, such as lubricating the springs and checking for signs of wear and damage, can help prolong the lifespan of your springs and ensure that your garage door operates safely and smoothly.

Signs that your garage door springs may need to be replaced include:

  • The door is difficult to open or close, or it feels heavy or unbalanced.
  • The springs look stretched out or warped.
  • The springs are making unusual noises, such as squeaking or creaking.
  • There are gaps between the coils of the springs.
  • The door is not opening or closing smoothly or evenly.

In conclusion, as stated in Garage Door Boynton Beach FL, if you’re experiencing any of these issues with your garage door, it’s important to consult with a professional garage door technician. They can help assess the condition of your springs and recommend the best course of action, whether that’s repair, maintenance, or replacement. It’s important to handle garage door spring replacement with caution, as the springs are under high tension and can pose a safety risk if not handled properly. A professional garage door technician will have the knowledge and equipment necessary to safely replace your springs and ensure that your garage door operates smoothly and safely.

Garage Door Experts of Boynton Beach

615 NE 7th Ave, Boynton Beach, FL 33435

561-861-2357

How to Change Garage Door Frequency – Garage Door Experts of Lake Worth

By

On March 23, 2023

In Garage Door

Changing the frequency of your garage door opener may be necessary if you are experiencing interference from other electronic devices or if you need to replace a garage door opener remote that is no longer working.

Here are the steps from Lake Worth Garage Door to change your garage door frequency:

Step 1: Determine the Current Frequency First, determine the current frequency of your garage door opener. You can find this information in the user manual or on the back of the opener itself. The most common frequencies are 315 MHz or 390 MHz, but newer models may use frequencies as high as 900 MHz.

Step 2: Purchase a New Receiver and Remote If you are changing the frequency because of interference or a malfunctioning remote, you will need to purchase a new receiver and remote that are compatible with the new frequency. Be sure to choose a receiver and remote that are compatible with your garage door opener brand and model.

Step 3: Turn off Power to the Garage Door Opener Before beginning any work on the garage door opener, turn off power to the unit by unplugging it or turning off the circuit breaker that controls the opener.

Step 4: Remove the Old Receiver Locate the receiver unit on the garage door opener motor and remove it from its mounting bracket. Carefully disconnect the wires from the receiver and remove it from the garage door opener.

Step 5: Install the New Receiver Attach the new receiver to the mounting bracket and connect the wires to the appropriate terminals. Follow the manufacturer’s instructions carefully to ensure that the wiring is correct.

Step 6: Program the New Remote Once the new receiver is installed, program the new remote to communicate with the garage door opener. This process will vary depending on the brand and model of the remote, so refer to the user manual for specific instructions.

Step 7: Turn on Power to the Garage Door Opener After programming the new remote, turn on power to the garage door opener and test the new remote to ensure that it is functioning properly.

Step 8: Adjust the Limits and Force Settings If the garage door does not open or close properly after changing the frequency, you may need to adjust the limits and force settings on the opener. Refer to the user manual for specific instructions on how to adjust these settings.

In conclusion, as stated in Lake Worth Garage Door, changing the frequency of your garage door opener is a relatively simple process that requires a new receiver and remote, as well as some basic electrical skills. By following these step-by-step instructions, you can ensure that your garage door opener is operating on the correct frequency and that your remote is functioning properly. If you are unsure about how to proceed or encounter any issues during the installation process, it’s always best to consult a professional garage door technician for assistance.

Garage Door Experts of Lake Worth

714 4th Ave N, Lake Worth, FL 33460

561-462-5171

How To Program A Universal Garage Door Opener – Strongsville Garage Door Repair

By

On March 23, 2023

In Garage Door

Programming a universal Garage Door Repair Strongsville OH opener involves a few basic steps. The process may vary slightly depending on the type and model of the opener, but the basic principles remain the same.

In this guide, we will walk you through the steps required to program a universal garage door opener:

Step 1: Check Compatibility

Before purchasing a universal garage door opener, it’s essential to check whether it’s compatible with your garage door opener. Some garage door openers use specific frequencies or codes, and not all universal remotes work with all garage door openers.

To check compatibility, you need to check the model number of your garage door opener and compare it to the list of compatible garage door openers provided by the manufacturer of the universal remote. If you cannot find the model number of your garage door opener, you may need to consult the owner’s manual or contact the manufacturer for assistance.

Step 2: Set the Remote

After confirming compatibility, you need to set the universal garage door opener remote to the correct mode. Some remotes have multiple modes, such as a learning mode or a dip switch mode. The mode you choose will depend on the type of garage door opener you have.

If your garage door opener uses a learning mode, you need to press and hold the button on the universal remote until the LED light flashes rapidly. Then press the button on the remote that you want to program, and hold it until the LED light stops flashing.

If your garage door opener uses a dip switch mode, you need to set the dip switches on the remote to match the dip switches on the garage door opener. This is typically done by opening the battery compartment on the remote and adjusting the dip switches using a small screwdriver.

Step 3: Program the Garage Door Opener

After setting the remote, you can proceed to program the garage door opener itself. To do this, you need to locate the “Learn” or “Smart” button on the garage door opener. This button is typically located on the back or side of the opener unit.

Once you’ve located the button, press it and release it quickly. The LED light on the garage door opener will start flashing. You then have approximately 30 seconds to press and hold the button on the universal remote that you want to program.

After holding the button down for a few seconds, the LED light on the garage door opener will stop flashing, indicating that the remote has been successfully programmed. You can test the remote by pressing the button to open or close the garage door.

Step 4: Repeat for Additional Remotes

If you have multiple universal remotes that you want to program, you need to repeat the same process for each one. You can program up to three remotes for most garage door openers, but this may vary depending on the model.

Step 5: Troubleshooting

If you encounter any problems during the programming process, there are a few things you can try to troubleshoot the issue. First, make sure that the batteries in the universal remote are fresh and fully charged. Weak or dead batteries can cause the remote to malfunction.

If the batteries are not the issue, you may need to reset the garage door opener and start the programming process over. To reset the opener, unplug it from the power source for a few seconds and then plug it back in. You can then proceed to program the remote as outlined above.

Conclusion:

Programming a universal Garage Door Repair Strongsville OH opener is a simple process that can be done in just a few steps. By following the steps outlined above, you can quickly and easily program a universal remote to work with your garage door opener. If you encounter any issues or have questions about the process, consult the owner’s manual or contact the manufacturer for assistance.

Strongsville Garage Door Repair

440-271-8232

Page 1 of 5

Next

Powered by WordPress & Theme by Anders Norén