We Select Texas Business Blog

The Largest Business Blog in Texas

Month: February 2023 Page 1 of 2

How to Replace Garage Door Seal – Argyle Garage Door Repair

By

On February 28, 2023

In Garage Door

Replacing a garage door seal is a simple process that can be done with a few basic tools and some patience.

In this guide, we will walk you through the steps to replace a Garage Door Repair Argyle TX seal:

Step 1: Measure the Garage Door Seal

The first step in replacing a garage door seal is to measure the existing seal. This will help you determine the length of the new seal you need to purchase. To measure the seal, close the garage door and measure the length of the seal along the bottom of the door. Make sure to measure the full length of the door, including any curves or angles.

Step 2: Purchase a New Garage Door Seal

Once you have measured the existing seal, you can purchase a new one from a hardware store or online retailer. Make sure to get the right length and type of seal for your garage door. There are several types of garage door seals available, including bottom seals, threshold seals, and weather-stripping seals.

Step 3: Remove the Old Garage Door Seal

To remove the old garage door seal, start by opening the garage door. Next, locate the seal along the bottom of the door. You may need to use a pry bar or pliers to remove any nails or staples holding the seal in place. Once the seal is free, pull it off the bottom of the door and discard it.

Step 4: Clean the Bottom of the Garage Door

Before installing the new seal, it’s important to clean the bottom of the garage door. Use a wire brush or scraper to remove any dirt, debris, or old adhesive from the surface. This will help the new seal adhere properly and ensure a tight seal.

Step 5: Install the New Garage Door Seal

To install the new garage door seal, start at one end of the door and position the seal so that the flat edge is flush against the bottom of the door. Make sure the seal is straight and in the correct position before attaching it. Use a staple gun or nails to secure the seal in place, making sure to space the fasteners evenly along the length of the seal.

Step 6: Test the Garage Door Seal

Once the new seal is installed, close the garage door and check the seal for any gaps or openings. If there are any gaps, adjust the seal as needed to ensure a tight fit. You can also test the seal by shining a flashlight under the closed door and looking for any light coming through.

Step 7: Trim the Excess Seal

If the new seal is longer than the length of the garage door, use a utility knife or scissors to trim off any excess material. Make sure to cut the seal straight and at a right angle to the bottom of the door.

Step 8: Apply Lubricant

To ensure the garage door operates smoothly, apply lubricant to the bottom of the door where the seal is attached. This will help the door slide smoothly over the seal and reduce wear and tear on the seal over time.

In conclusion, replacing a Garage Door Repair Argyle TX seal is a simple process that can be done with a few basic tools and some patience. By following these steps, you can install a new seal that will provide a tight, secure seal for your garage door and help keep out the elements.

Argyle Garage Door Repair

1004 Stonecrest Rd, Argyle, TX 76226, United States

1-940-326-5646

How to Line Up a Garage Door Sensors – BH Garage Door Repair of Forney

By

On February 28, 2023

In Garage Door

When I moved into my new house, one of the first things I noticed was that the garage door sensors were not properly aligned. The garage door would sometimes close partially and then reopen, which was quite frustrating.

So, I decided to align the sensors myself, and here is what I did based from Garage Door Repair Forney TX:

First, I gathered the necessary tools, including a tape measure, a level, a screwdriver, and a ladder. Then, I inspected the sensors to make sure they were clean and free of any debris or obstructions. Next, I checked the wiring connecting the sensors to the garage door opener to ensure they were secure and undamaged.

After checking the sensors, I moved on to adjusting their height. I used a tape measure to measure the height of each sensor from the ground. If there was a difference in height, I adjusted one of the sensors to match the other one. It was important to ensure that the sensors were installed at the same height, so they could function properly.

Next, I used a level to check if the sensors were installed straight. I placed the level vertically against each sensor to ensure that they were level. If the sensors were not level, I adjusted them accordingly by loosening the screws that held them in place and aligning them with the level.

Once I had adjusted the height and ensured that the sensors were level, I aligned them with each other. The sensors have a small light indicator that should be aligned with each other. The indicator light on one sensor should be directly facing the indicator light on the other sensor. I used a piece of string to help me align the sensors correctly. I tied the string between the sensors and adjusted them until the indicator lights were aligned with the string.

After aligning the sensors, I tested them to ensure they were functioning correctly. I opened the garage door and placed an object in the path of the sensors. The door should stop closing and reverse direction if the sensors are working correctly. If the door did not stop or reversed direction too soon, I made further adjustments.

Finally, I tightened the screws that held the sensors in place once I was satisfied that they were properly aligned and functioning correctly. It was important to remember to clean and inspect the sensors regularly to prevent any issues.

In conclusion, according to Garage Door Repair Forney TX, aligning garage door sensors was not as difficult as I initially thought it would be. It required a few simple tools and some patience, but it was a job that I was able to complete myself. I felt relieved knowing that the garage door would now close properly and safely every time.

BH Garage Door Repair of Forney

108 E Main St, Forney, TX 75126

469-820-3581

How to Test Your Garage Door Sensors? – Right on Time Garage Doors of San Antonio

By

On February 28, 2023

In Garage Door

I recently noticed that my garage door was not closing when I pressed the remote button. At first, I thought it was an issue with the remote, but after replacing the batteries, the problem persisted.

I then realized that it could be an issue with the sensors, so I decided to test them based from Garage Door Repair Denison TX.

The first thing I did was clear the area around the sensors. I removed any debris or objects that were blocking them. Next, I made sure that the power to the garage door opener was turned on and checked the LED lights on the sensors. The LED light on one of the sensors was not illuminated, which indicated that there was an issue with that sensor.

To test the sensors further, I used a cardboard box to simulate an obstruction in the path of the door. I placed the box in front of one of the sensors and attempted to close the door using the remote. The door did not close, and the opener beeped to indicate that there was an obstruction. I repeated this process for the other sensor, and the door did not close again.

Since the door did not close with either sensor, I suspected that it was an alignment issue. I used a level to ensure that both sensors were level and pointed directly at each other. After adjusting the sensors, I retested them with the cardboard box. This time, the door did not close when the box was in front of the sensors, which indicated that the sensors were now functioning correctly.

Finally, I cleaned the lenses of the sensors with a soft, dry cloth and tested them again to ensure that they were still functioning properly. This time, the door closed without any issues.

In conclusion, based from Garage Door Repair Denison TX, testing garage door sensors is an essential part of garage door maintenance. By following these steps, I was able to identify and fix an issue with my sensors and ensure that my garage door was operating safely. Regular testing and maintenance of garage door sensors can help prevent accidents and ensure that your garage door operates efficiently.

Right on Time Garage Doors of San Antonio

341 St Cloud, San Antonio, TX 78228

210-963-5866

How to Measure Your Garage Door? – Princeton Garage Door Experts

By

On February 27, 2023

In Garage Door

Measuring a garage door is an essential step in the process of purchasing a new door or replacing an old one.

The following is a step-by-step guide from Garage Door Repair Princeton TX on how to measure a garage door:

The first step I took was to clear the area around the garage door. I moved any items that might interfere with the measurement process.

Next, I measured the width of the garage door opening by measuring from one side of the opening to the other at the widest point. I included any trim around the opening in the measurement.

After that, I measured the height of the garage door opening by measuring from the floor to the top of the opening at the highest point. I also included any trim around the opening in the measurement.

Then, I measured the headroom, which is the space between the top of the garage door opening and the ceiling or any overhead obstacles. I measured from the top of the opening to the ceiling at the lowest point.

Next, I measured the backroom, which is the distance between the garage door opening and the back wall of the garage. I measured from the inside of the opening to the back wall at the deepest point.

Finally, I measured the side room, which is the distance between the garage door opening and the side wall of the garage. I measured from the inside of the opening to the side wall at the widest point.

Once I had all the measurements, I used a level to check that the floor and sides of the opening were level, and a plumb line to check that the sides of the opening were straight.

Finally, I considered the type of door needed for my garage based on the thickness of the door, the size and shape of the windows (if applicable), and the type of material the door is made from. I also thought about the climate and weather conditions in my area when choosing a garage door.

Overall, based from Garage Door Repair Princeton TX, measuring a garage door is a straightforward process that involves measuring the width, height, headroom, backroom, and side room of the opening. It’s important to take accurate measurements and ensure that the opening is level and plumb before purchasing a new door. By following these steps, I can ensure that I purchase the right size and type of door for my garage.

Princeton Garage Door Experts

114 N 2nd St #5, Princeton, TX 75407, United States

469-281-7310

How to Open a Garage Door Manually – Dragon Garage Door & Gates

By

On February 24, 2023

In Garage Door

Opening a garage door manually is an important skill to have in case of a power outage or malfunction with the automatic opener.

In this guide, we’ll walk you through the steps to manually open a Garage Door Repair Southlake TX safely and efficiently.

Step 1: Disconnect the Automatic Opener The first step to opening a garage door manually is to disconnect the automatic opener. This is an essential safety step to ensure that the garage door doesn’t accidentally open or close while you’re manually operating it. Locate the emergency release cord, which is usually a red rope or handle that hangs from the automatic opener track. Pull this cord or handle down to disconnect the trolley from the opener carriage.

Step 2: Unlock the Door Next, you need to unlock the garage door. If your garage door has a manual lock, insert the key into the lock and turn it clockwise to unlock the door. If your garage door doesn’t have a manual lock, you can skip this step and move on to the next one.

Step 3: Lift the Door Once the automatic opener is disconnected and the door is unlocked, you can lift the door manually. Place your hands on the bottom of the garage door, just above the rollers, and lift the door straight up. Be sure to keep your feet clear of the door as you lift it.

Step 4: Secure the Door After you’ve lifted the door, you need to secure it in the open position. Most garage doors have a lock bar that you can use to secure the door. The lock bar is usually located on the inside of the garage door and can be slid into place to prevent the door from closing. If your garage door doesn’t have a lock bar, you can use a C-clamp to hold the door in place. Simply place the C-clamp on the track just above one of the rollers and tighten it until the door is securely held in place.

Step 5: Test the Door Once you’ve manually opened the garage door, it’s important to test it to make sure it’s functioning properly. Close the door manually and ensure that it closes smoothly and doesn’t bind or catch on anything. If there are any issues with the door’s operation, stop using it immediately and consult a professional garage door technician for repairs.

Step 6: Reconnect the Automatic Opener After you’ve manually opened and closed the garage door, it’s time to reconnect the automatic opener. To do this, simply pull the emergency release cord again to release the trolley, then press the button on your remote or wall control to reconnect the opener. The trolley should automatically re-engage with the opener carriage and the garage door should be ready to operate with the automatic opener again.

Safety Tips for Opening a Garage Door Manually Opening a garage door manually can be dangerous if proper safety precautions aren’t taken. Here are some important safety tips to keep in mind:

  • Always disconnect the automatic opener before attempting to manually operate the garage door.
  • Keep your hands and feet away from the garage door as you lift it manually.
  • Use caution when securing the door in the open position to prevent it from falling or closing unexpectedly.
  • Test the door’s operation before using it again with the automatic opener.
  • If you experience any issues with the door’s operation, stop using it immediately and consult a professional garage door technician for repairs.

Conclusion Knowing how to open a Garage Door Repair Southlake TX manually is an essential skill for any homeowner. By following the steps outlined in this guide and taking proper safety precautions, you can safely and efficiently open your garage door manually in case of a power outage or malfunction with the automatic opener.

Dragon Garage Door & Gates

351 Central Ave #7, Southlake, TX 76092, United States

1-817-587-0445

How to Install a Garage Door Spring – Murphy Garage Door & Gates

By

On February 24, 2023

In Garage Door

As a disclaimer, installing garage door springs can be dangerous and should only be attempted by individuals with experience and proper equipment. It’s important to follow safety procedures and manufacturer instructions carefully to avoid injury or damage to the garage door.

As stated in Garage Door Repair Murphy TX, I can provide step-by-step instructions on how to install garage door springs safely and efficiently.

To install a garage door spring, I first release the tension on the old spring by unwinding it from the torsion bar using winding bars. I remove the old spring and install the new spring in its place.

Next, I insert the torsion bar into the center bracket of the garage door and secure it with the center bearing plate and bolts. I slide the left bracket onto the torsion bar, making sure it is flush with the wall and level. Then, I slide the right bracket onto the torsion bar, making sure it is level and flush with the wall.

I then wind the new spring using the winding bars, making sure to wind it in the correct direction specified by the manufacturer. I keep track of the number of turns I make, and wind the spring to the correct tension for the weight of the garage door.

After winding the spring, I attach the cables to the bottom brackets and the cable drum, making sure they are properly tensioned. I install the cable drum onto the torsion bar and tighten the set screws.

Next, I install the lift cables onto the cable drums and attach the other end to the bottom brackets on the garage door. I make sure the cables are properly aligned and tensioned.

Before finishing up, I test the garage door to make sure it operates correctly. I open and close it several times, making sure it moves smoothly and the cables and springs are properly tensioned. I adjust the tension if necessary.

In summary, based from Garage Door Repair Murphy TX, It’s important to note that installing garage door springs can be dangerous, and should only be attempted by individuals with experience and proper equipment. If in doubt, it’s always best to hire a professional garage door technician to install the springs for you.

Murphy Garage Door & Gates

223 FM 544 #16, Murphy, TX 75094, United States

469-425-7816

How to Reset Chamberlain Garage Door Opener – Grayson County Garage Door Repair

By

On February 24, 2023

In Garage Door

If you need to reset your Chamberlain garage door opener, here are the steps I recommend as stated in Garage Door Repair Sherman TX:

Step 1: First, I identify the model of my Chamberlain garage door opener by checking the back of the motor unit for the model number. This will help me determine the specific steps I need to take to reset the opener.

Step 2: I disconnect the power by locating the power cord that is connected to the motor unit and unplugging it from the power outlet. If my Chamberlain garage door opener is hardwired, I turn off the circuit breaker that supplies power to the opener.

Step 3: I wait for approximately 30 seconds to give the garage door opener time to fully power down.

Step 4: I restore power to the garage door opener by reconnecting the power cord to the motor unit or turning the circuit breaker back on if the opener is hardwired. I wait for the motor unit to power up completely.

Step 5: To reset the remote control and keypad, I locate the “learn” button on the motor unit. I press and hold the “learn” button for approximately 10 seconds or until the indicator light on the motor unit turns on and then off. This erases any previously programmed remote controls and keypads.

Step 6: To reprogram the remote control and keypad, I press the “learn” button on the motor unit and then press the button on the remote control that I want to program. I repeat this process for each additional remote control. To program the keypad, I press the “learn” button twice on the motor unit and then enter the 4-digit code that I want to use on the keypad. I press the “enter” button to complete the programming process.

Step 7: Finally, I test the garage door opener by using the remote control or keypad to operate the opener and ensure that it opens and closes smoothly.

Overall, based from Garage Door Repair Sherman TX resetting a Chamberlain garage door opener is a simple process that anyone can do. Just make sure to identify the model of your garage door opener before beginning the reset process, and follow the specific steps for your model to ensure a successful reset.

Grayson County Garage Door Repair

1940 Everheart Rd, Bells, TX 75414, United States

903-500-7205

How to Install Garage Door – South Denton Overhead Garage Door

By

On February 23, 2023

In Garage Door

Before starting, it’s important to note that installing a Garage Door Repair Roanoke TX is a two-person job and requires some experience with power tools. If you’re not confident with DIY projects, it’s best to hire a professional.

Step 1: Gather the tools and materials

To start, you’ll need the following tools and materials:

  • A garage door kit
  • A power drill
  • A level
  • A tape measure
  • A saw
  • A ladder
  • A hammer
  • A screwdriver
  • Bolts, nuts, and screws
  • Winding bars
  • Weatherstripping

Step 2: Measure the opening

Measure the width and height of the garage opening to ensure that the door fits properly. Take accurate measurements of the width and height of the opening at several points to ensure that the opening is square.

Step 3: Assemble the door sections

Assemble the garage door sections according to the manufacturer’s instructions. Depending on the type of door you have, this may involve attaching hinges, rollers, and tracks.

Step 4: Install the tracks

Attach the horizontal and vertical tracks to the wall using the supplied brackets. Make sure the tracks are level and plumb by using a level.

Step 5: Install the springs

Install the torsion springs on the torsion bar above the door. Make sure the springs are secure and properly tensioned. Use winding bars to wind the springs to the correct tension.

Step 6: Hang the door

With the help of a second person, lift the garage door into place and attach it to the tracks. Make sure the door is level and plumb.

Step 7: Install the rollers

Attach the rollers to the door sections and track. Make sure the rollers move smoothly along the track.

Step 8: Install the weatherstripping

Install weatherstripping along the bottom of the door to prevent drafts and keep out debris.

Step 9: Install the opener

Install the garage door opener according to the manufacturer’s instructions. Make sure the opener is securely attached to the ceiling and that the rail is attached to the motor.

Step 10: Test the door

Test the garage door to make sure it opens and closes smoothly. Adjust the tension on the springs if necessary.

Step 11: Attach the safety features

Attach safety features such as the safety sensors and emergency release cord to the garage door opener. These are important safety features that prevent the door from closing on people or objects.

Step 12: Finish the installation

Finally, finish the installation by attaching any remaining hardware such as handles and locks. Make sure all screws and bolts are tight.

Conclusion:

Installing a Garage Door Repair Roanoke TX is a challenging but rewarding task. With the right tools and knowledge, you can complete this project and enjoy the benefits of a new garage door. Remember to take safety precautions and enlist the help of a second person if necessary.

South Denton Overhead Garage Door

112 US-377 #9, Roanoke, TX 76262, United States

1-817-873-2942

How to Program Garage Door Opener to a Car – BH Garage Door & Gates of Celina

By

On February 23, 2023

In Garage Door

I recently programmed my garage door opener to my car, and it was surprisingly easy to do. Programming your garage door opener to your car is a convenient way to open and close your garage door without having to get out of your car.

Here’s how to program your garage door opener to your car in reference to Garage Door Repair Celina TX:

I started by gathering all the supplies I needed, which included my garage door opener remote, my car’s owner’s manual, a step ladder, and safety glasses.

Next, I located the “learn” button on my garage door opener motor, which was located on the back of the unit. I consulted my garage door opener manual to be sure I had found the right button.

After that, I chose which button on my car’s remote I wanted to program for my garage door opener. I chose the middle button, which was unused and easy to access.

Then, I pressed and held the “learn” button on my garage door opener until the light started blinking. I held the button for a few seconds until I saw the light turn off and then back on again.

While the garage door opener was in programming mode, I pressed and held the button on my car’s remote that I wanted to use for my garage door opener. I held the button until the garage door opener’s light blinked or turned off and then back on again.

Finally, I tested the garage door opener by parking my car outside the garage and pressing the button I had just programmed on my car’s remote. The garage door opened smoothly, indicating that the programming was successful.

Overall, as stated in Garage Door Repair Celina TX, programming my garage door opener to my car was a simple and convenient task that I’m glad I took the time to do. Now I can easily open and close my garage door without having to get out of my car.

BH Garage Door & Gates of Celina

102 N Ohio St #4A, Celina, TX 75009, United States

214-949-4432

How to Install a Garage Door- Garage Door Experts of Azle

By

On February 22, 2023

In Garage Door

Installing from a Garage Door Repair Azle TX can be a challenging task, but with the right tools and knowledge, it can be done.

The following steps will guide you through the process of installing a Garage Door Repair Azle TX.

Tools and Materials Needed:

Before you start installing the garage door, you will need the following tools and materials:

  • Garage door kit (includes tracks, panels, and hardware)
  • Electric drill
  • Hammer
  • Screwdriver
  • Level
  • Tape measure
  • Sawhorses
  • Ladder
  • Bolts and nuts
  • Wrench

Step 1: Gather Required Information

Before you start the installation process, you need to gather some information about your garage. This information includes the size of the garage door opening, the ceiling height, and the headroom space.

Step 2: Assemble the Tracks

The garage door tracks need to be assembled before you can begin installation. Follow the instructions provided with the garage door kit to assemble the tracks. Typically, the tracks will come in several pieces that need to be joined together with bolts and nuts.

Step 3: Install the Tracks

Install the vertical tracks first, then attach the horizontal tracks. Use a level to make sure the tracks are level and plumb. Secure the tracks to the walls with brackets and fasteners.

Step 4: Install the Springs

The springs need to be installed on the garage door before it can be lifted into place. Use a ladder to reach the top of the garage door and attach the springs to the brackets. Follow the instructions provided with the garage door kit to ensure proper installation.

Step 5: Attach the Panels

Once the tracks and springs are in place, attach the panels to the tracks. Be sure to follow the instructions provided with the garage door kit to ensure that the panels are installed correctly.

Step 6: Install the Rollers

Install the rollers onto the garage door panels. This will allow the garage door to move smoothly along the tracks.

Step 7: Install the Opener

If your garage door kit comes with an opener, install it according to the manufacturer’s instructions. The opener should be mounted to the ceiling and connected to the garage door.

Step 8: Test the Garage Door

Once the installation is complete, test the garage door to make sure it is functioning properly. Open and close the door several times to ensure that it moves smoothly and quietly.

Step 9: Make Adjustments

If necessary, make adjustments to the garage door to ensure that it is operating properly. This may include adjusting the springs, tracks, or opener.

Step 10: Enjoy Your New Garage Door!

Congratulations, you have successfully installed a garage door! Enjoy the added convenience and security that a garage door provides. Remember to maintain the door and opener to ensure that they continue to operate smoothly and safely.

Garage Door Experts of Azle

525 Commerce St #5, Azle, TX 76020, United States

1-817-5184880

Page 1 of 2

Next

Powered by WordPress & Theme by Anders Norén