We Select Texas Business Blog

The Largest Business Blog in Texas

Month: January 2023

How to Change Battery in Garage Door Opener – Ohio Garage Door Repair

By

On January 28, 2023

In Garage Door

Here’s a step-by-step guide on how I personally change the battery in my garage door opener based from Garage Door Repair Services:

  1. First, I gather the necessary tools and equipment. I make sure to have a small flathead screwdriver or a coin, and a replacement battery that matches the required specifications of my garage door opener. It’s important to check the manufacturer’s instructions or the label on the battery compartment to ensure the correct battery type.
  2. With the tools and battery ready, I locate the battery compartment on my garage door opener. It is usually located on the back or side of the main housing unit. In some models, the battery compartment may be on the front panel. I take a moment to familiarize myself with the layout and design of the compartment.
  3. Using the small flathead screwdriver or a coin, I carefully open the battery compartment. If there is a slot for turning, I insert the coin and turn it counterclockwise to loosen the cover. If there is a small screw, I use the flathead screwdriver to remove it and lift off the cover. I set aside the cover in a safe place where it won’t get lost.
  4. Inside the battery compartment, I see the old battery. I take note of its orientation before removing it to ensure I insert the new battery correctly. If there is a small clip holding the battery in place, I release it or gently push the battery to the side to disengage it. If there is a spring mechanism, I press it down or to the side to release the battery.
  5. Once the old battery is free, I carefully remove it from the compartment, making sure not to touch any metal contacts. I set the old battery aside for proper disposal later, following the local regulations for battery disposal.
  6. Now, I take the new battery and check its polarity, ensuring it matches the correct orientation indicated in the battery compartment. If the positive (+) and negative (-) signs are labeled, I align the new battery accordingly. I insert the new battery into the compartment, making sure it fits securely.
  7. With the new battery in place, I position the cover back onto the battery compartment. If there is a screw, I insert it and use the flathead screwdriver to tighten it. If there is a slot, I align the cover and turn it clockwise until it is securely fastened. I double-check to ensure the cover is properly closed.
  8. Now it’s time to test the garage door opener with the new battery. I stand away from the door and use either the remote control or the wall-mounted control panel to operate the garage door. I press the appropriate button to open and close the door, observing its smooth operation. If the door responds well without any issues, the battery replacement was successful.
  9. Finally, I make sure to dispose of the old battery responsibly. I follow the local guidelines for battery recycling and take the old battery to a designated recycling center or a collection point. Proper disposal helps protect the environment and ensures the safe handling of hazardous materials.

By following these steps from Garage Door Repair Services, I can easily change the battery in my garage door opener, ensuring that it continues to function reliably. Regularly replacing the battery when needed helps prevent any interruptions in the operation of the garage door opener and keeps it running smoothly.

Ohio Garage Door Repair

7201 Longview Dr, Solon, OH 44139

440-773-2246

How to Repair Garage Door Opener – First Responder Garage Doors

By

On January 27, 2023

In Garage Door

When it comes to repairing a garage door opener, I understand the importance of following a systematic approach.

Here’s how I would go about it as stated in Garage Door Repair:

Step 1: Identify the Problem The first thing I do is identify the specific problem with my garage door opener. Whether it’s a motor issue, a wiring problem, or a malfunctioning sensor, understanding the root cause is essential for an effective repair.

Step 2: Disconnect the Power To ensure my safety, I always disconnect the power to the garage door opener. I unplug it from the electrical outlet or switch off the circuit breaker that supplies power to the opener. This step prevents any accidental electrical shocks while working on the opener.

Step 3: Inspect the Opener I thoroughly inspect the opener for any visible damage or signs of wear and tear. I check the wiring connections, motor assembly, gear system, and control panel. If I notice any loose components, I tighten them securely.

Step 4: Troubleshoot Remote Control Issues If the problem lies with the remote control, I start by checking the batteries. I replace them if necessary. I ensure that the remote control is within range and that there are no obstacles blocking the signal between the remote and the opener.

Step 5: Reset or Reconfigure the Opener If the opener is unresponsive or behaving erratically, I attempt to reset or reconfigure it. I refer to the manufacturer’s manual for specific instructions on how to perform a reset or reconfiguration. This often involves pressing certain buttons or accessing a reset button on the opener itself.

Step 6: Lubricate Moving Parts I understand the importance of regular lubrication to ensure smooth operation. I apply a silicone-based lubricant to the roller tracks, hinges, and springs of the garage door. This helps reduce friction and prevents premature wear and tear.

Step 7: Check and Align the Sensors If my garage door opener has safety sensors, I inspect them for proper alignment and cleanliness. I make sure there are no obstructions blocking the sensor’s path and clean the lenses if needed. Aligning the sensors correctly is crucial for the safe operation of the garage door.

Step 8: Test Safety Features To ensure the safety features of the garage door opener are functioning correctly, I conduct a series of tests. I check the auto-reverse function by placing a small object, such as a block of wood, in the path of the closing door. The door should automatically reverse when it comes into contact with the object.

Step 9: Consult a Professional if Necessary If I have exhausted all my troubleshooting efforts and the garage door opener still doesn’t work properly, I know it’s time to seek professional help. Garage door opener repairs can be complex, and a trained technician has the expertise and tools to handle the task safely and efficiently.

It’s important to note that garage door opener repairs can be challenging and potentially dangerous. If at any point I feel unsure or uncomfortable with the repair process, I always rely on a professional technician to get the job done right.

Remember, according to Garage Door Repair, safety is paramount when working on garage door openers, so it’s crucial to take all necessary precautions and seek professional help when needed.

First Responder Garage Doors

180 State St. #225, Southlake, TX. 76092

How to Fix Garage Door – Arnold’s Garage Door Service

By

On January 26, 2023

In Garage Door

Recently, I encountered an issue with my garage door where it wouldn’t open or close properly. It was frustrating, but I decided to tackle the problem myself.

Here’s what I did according to Garage Door Repair:

  1. Garage door won’t open or close:
    • First, I checked the power source. I made sure that the garage door opener was plugged in securely and receiving power. I also tested the power outlet with another device to ensure it was working.
    • Next, I inspected the remote control. I replaced the batteries and made sure it was programmed correctly. I also tried using the wall-mounted control panel to see if that made a difference.
    • One of the most common causes of this issue is misaligned safety sensors. I checked the sensors located near the bottom of the door on each side to ensure they were aligned properly and not obstructed. I cleaned them and made sure their LED lights were lit and not blinking.
  2. Garage door is noisy:
    • To address the noise issue, I lubricated the moving parts of the door. I used a silicone-based lubricant and applied it to the rollers, hinges, tracks, and springs. This helped to reduce friction and eliminate the annoying noise.
    • I also took the time to tighten any loose hardware. I carefully inspected all the nuts, bolts, and screws, especially on the hinges, brackets, and track supports. By tightening them, I eliminated any rattling or shaking noises caused by loose hardware.
  3. Garage door is off-track:
    • When my garage door went off-track, I knew I had to take immediate action. I started by disconnecting the opener using the emergency release handle. This allowed me to move the door manually without any resistance.
    • I carefully inspected the tracks for any obstructions, such as debris or dents. I removed any debris and used a rubber mallet to gently tap misaligned sections back into place. I ensured that the tracks were properly aligned and level.
    • With the help of another person, I lifted the door slowly and evenly, guiding it back onto the tracks. Once aligned, I lowered the door and tested its movement to ensure it was back on track.
  4. Garage door springs are broken:
    • I must emphasize that dealing with broken garage door springs can be dangerous, so I proceeded with caution. If you’re uncertain or uncomfortable with this repair, it’s best to call a professional.
    • I first identified the type of springs I had. In my case, they were extension springs located alongside the door tracks.
    • Following the manufacturer’s instructions, I carefully removed the broken springs and replaced them with new ones. I ensured that the new springs were installed correctly and adjusted their tension as needed.
  5. Garage door is unbalanced:
    • To fix an unbalanced garage door, I started by disconnecting the opener using the emergency release handle.
    • I manually operated the door by lifting it halfway and then releasing it. If the door stayed in place, it indicated that the balance was fine. However, if it fell or rose, I knew it needed adjustment.
    • Adjusting the spring tension was the next step. In my case, I had torsion springs, and I used an adjustment rod inserted into the spring cone. By turning the rod incrementally, I was able to increase or decrease the spring tension until the door was properly balanced.

In my experience and by following Garage Door Repair, addressing these common garage door problems was possible with a bit of patience and careful attention to detail. However, it’s important to remember that each situation is unique, and it’s always wise to consult a professional if you’re unsure or uncomfortable with any repair. They have the expertise and knowledge to handle complex garage door issues safely.

Arnold’s Garage Door Service

2129 Tippy Ter, Fort Worth, TX 76134

682-261-6268

How to Install Weather Stripping on Garage Door – Denzel’s Garage Doors

By

On January 13, 2023

In Garage Door

I recently decided to improve the energy efficiency and insulation of my garage by installing weather stripping on the garage door. In this personal step-by-step guide, I will share the process I followed to successfully install weather stripping on my garage door. By doing so, I was able to reduce drafts, noise, and enhance the overall comfort of my garage space.

Section 1

By following steps from Garage Door Repair Services, gather the Materials To begin the installation, I made sure to gather all the necessary materials and tools. I measured the width and height of my garage door to determine the length of weather stripping needed. Based on my door’s material and design, I selected adhesive-backed foam tape as the most suitable weather stripping option. For the installation, I needed a utility knife, tape measure, pliers, screwdriver, clean cloth, mild detergent, and the weather stripping itself.

Section 2

Prepare the Garage Door Before installing the weather stripping, I made sure to prepare the garage door surface. I cleaned the areas where the weather stripping would be attached using a clean cloth and a mild detergent solution. This step removed any dirt, grease, or debris and ensured a smooth surface for proper adhesion. After cleaning, I made sure to thoroughly dry the surface before proceeding.

Section 3

Installing Top and Side Weather Stripping I began the installation by measuring and cutting the weather stripping for the top and sides of the garage door. Using a tape measure, I marked the appropriate lengths on the weather stripping material. With a utility knife, I carefully cut along the marked lines, ensuring clean and straight cuts. Next, I peeled off the adhesive backing from the weather stripping and started attaching it to the edge of the door, pressing firmly and gradually along the entire length. I made sure the weather stripping adhered securely and evenly. I repeated the same process for the other side(s) of the garage door, ensuring proper alignment and a snug fit. If there was any excess weather stripping, I trimmed it accordingly.

Section 4

Installing Bottom Seal To complete the installation, I moved on to installing the bottom seal. I measured the width of the garage door’s bottom section and marked the appropriate length for the bottom seal. Using a utility knife, I cut the bottom seal along the marked lines. I then positioned the bottom seal along the bottom edge of the garage door, ensuring it was aligned properly. If the bottom seal had pre-drilled holes, I lined them up with the existing holes on the garage door. If not, I created new holes using a screwdriver. I secured the bottom seal in place using the provided screws, making sure they were suitable for my door material.

Section 5

Finishing Touches Once the weather stripping and bottom seal were installed, I tested the garage door to ensure proper alignment and function. I closed the door and checked for any obstructions or misalignments caused by the weather stripping. I made necessary adjustments to ensure smooth opening and closing without excessive friction. Finally, I stood back and admired the newly installed weather stripping, knowing that I had taken a step towards a more energy-efficient and comfortable garage.

Conclusion

Overall, according to Garage Door Repair Services, installing weather stripping on my garage door was a rewarding DIY project that significantly improved the insulation and comfort of my garage space. By following these steps and taking the time to properly measure, cut, and attach the weather stripping, I was able to achieve effective sealing against drafts and reduce noise. With a few simple tools and a bit of effort, anyone can successfully install weather stripping on their garage door and enjoy the benefits it provides.

Denzel’s Garage Doors

Marina Del Ray, CA

619-496-9419

How to Reset Xtreme Garage Door Opener-Atlas Door Company

By

On January 4, 2023

In Garage Door

Resetting an Xtreme Garage Door Repair Opener is a straightforward process that can be completed in just a few steps. By following these instructions carefully, you’ll be able to reset your garage door opener and restore it to its factory settings.

Before starting the reset process, make sure you have the necessary tools and equipment, including a ladder, a flathead screwdriver, and the instruction manual for your specific model.

  1. Safety first: Before attempting any work on your garage door opener, ensure that the power is disconnected to prevent any accidental injuries. Locate the power source for your garage door opener and unplug it from the electrical outlet.
  2. Clear the memory: To reset your Xtreme Garage Door Opener, you’ll need to clear its memory. Look for the “Learn” or “Program” button on the opener’s main unit. This button is typically located near the antenna wire or on the back of the unit. Press and hold the “Learn” or “Program” button for about 10 seconds until the indicator light turns off.
  3. Access the remote control: Next, you’ll need to reset the remote control that operates your garage door opener. Open the battery compartment on the back of the remote control and remove the batteries. Leave the batteries out for about 30 seconds to ensure a complete reset. This step is crucial to ensure that the remote control is ready to be reprogrammed.
  4. Reprogram the remote control: After the 30-second interval, reinsert the batteries into the remote control. Stand within range of the garage door opener (usually within 20-30 feet) and press the “Learn” or “Program” button on the main unit once. The indicator light should turn on, indicating that the unit is in programming mode.
  5. On the remote control, press and hold the button you want to use to operate the garage door. This button could be labeled as “Open,” “Close,” or another suitable designation. Hold the button down until the indicator light on the main unit blinks, usually for about 2-3 seconds. This process associates the button on the remote control with the garage door opener.
  6. Test the remote control: To ensure successful programming, test the remote control by pressing the button you just programmed. The garage door should respond by opening or closing. If it doesn’t, repeat steps 4 and 5, ensuring that you’re within range of the main unit.
  7. Resetting additional remote controls and keypads: If you have additional remote controls or keypads that need to be reset, repeat steps 3 to 6 for each device. Remember to remove the batteries, wait for 30 seconds, and reinsert them before programming.
  8. Resetting the opener’s limits and force settings (optional): In some cases, you may need to reset the limits and force settings on your Xtreme Garage Door Opener. Consult the instruction manual for your specific model to determine the exact procedure for doing this, as it may vary. Usually, it involves adjusting the limit screws on the main unit using a flathead screwdriver.
  9. Restore power: Once you’ve completed the necessary resets and reprogramming, restore power to the garage door opener by plugging it back into the electrical outlet. The unit should be ready for regular operation.

Remember, these instructions are general guidelines, and the specific steps may vary depending on your model of Xtreme Garage Door Repair Opener. Consult the instruction manual that came with your device for detailed instructions tailored to your specific unit. If you encounter any difficulties or are unsure about any step, it’s always recommended to contact the manufacturer’s customer support for further assistance.

Atlas Door Company

6817 Sundance Cir W, Joshua, TX 76058, United States

1-817-295-3660

Powered by WordPress & Theme by Anders Norén